Power Cable Wire

Control Cable

2014-10-08T09:03:00.000-07:00

Control cable is intended for fixed connection to electric units, apparatus and clips of electrical distributing units. Control cable is used for signal units, control units, relay protection e.t.c.

Nominal voltage A.C. up to 100 Hz, [V] 660
Nominal voltage D.C., [V] 1000
Test voltage A.C. 50 Hz, 5 minutes, [V] 2500
Max. operating temperature of conductor, [°C] +70
Temperature of environment, [°C] -50/+50
Humidity at 35°C, [%] 98
Installation at temperature, not less than, [°C]:
- for non-armoured cables -15
- for armoured cables -7
Length of cable, not less, [m] 150
Lifetime of cables, not less than, [year]:
- in the open air and soil 15
- in premises, conduit and ducts 25
Guarantee period, [year] 3

Control cable КВВГ:
1. Conductor. 2. Insulation. 3. Outer sheath.
Control cable АКВБбШв:
1. Conductor. 2. Insulation. 3. Bedding. 4. Armour. 5. Bitumen. 6. PETF tape. 7. Outer sheath.

Browse the categories on the page to search the necessary control cable and wire.
Visit our capabilities page to learn more about materials offerings.

Application:

Cables are used for connection to electric units, apparatus, clamps, switch gears with altemating voltage up to 660 V, frequency up to 100 Hz or direct voltage up to 1000 V.

Cables should be installed in fixed electric networks. If there is danger of mechanical damage during operation it is recommended to use armored cables.

For installation outdoors, in premises, ducts, channels, in aggressive environment, if there is no mechanical influence to cable. Do not distribute burning in case of single laying (IEC 60332-1) (control cables КВВГ, АКВВГ).

The same as control cable АКВВГ, but do not distribute burning in case of laying in bundles (IEC 60332-3, category A) (АКВВГнг).

The same as control cable КВВГ, but do not distribute burning in case of laying in bundles (IEC 60332-3, category A). Low smoke at burning (IEC 61034-1, 2) (КВВГнг-LS).

For network which require protection of electric circuits from the influence of outer electric fields. Do not distribute burning in case of single laying (IEC 60332-1) (КВВГЭ).

The same as control cable АКВВГЭ, but do not distribute burning in case of laying in bundles (IEC 60332-3, category A) (АКВВГЭнг).

The same as for similar to control cable КВВГЭ, but do not distribute burning in case of laying in bundles (IEC 60332-3, A categories). Low smoke at burning (IEC 61034-1, 2) (КВВГЭнг-LS).

For installation outdoors, in premises, ducts, channels, in aggressive environment, if there is a danger of mechanical influence to cable. If cable is not subject to considerable tensile strength. Do not distribute burning in case of single laying (IEC 60332-1) - exclud cable types АКВВБ, КВВБ (АКВВБ, КВВБ).

For installation in soil (trenches), in aggressive environment, in areas subject to stray currents influence, if cable is not subject to tensile efforts (КРВБ).

For installation outdoors, in premises, ducts, channels, in soil (trenches), in aggressive environment, in areas subject to stray currents influence, if the cable is not subject to tensile efforts and if there is a risk of mechanical influence to cable. Do not distribute burning in case of single laying (IEC 60332-1) (АКВБбШв, КВБбШв).

The same as control cable АКВБбШв, but if the cable is subject to tensile efforts (poured, boggy, distending and permafrost soils, vertical lines) (КВПбШв).

The same as control cable КВБбШв. Do not distribute burning in case of laying in bundles (IEC 60332-3, A and B categories) (КВБбШнг).

Cable Wire
Electrical Cables for Fixed Installation. Part 1
Power Cable

Power Cable with PVC Insulation

2009-10-11T07:44:00.000-07:00

Power cables are intended for transmission and distribution of power in fixed network.

Nominal voltage A.C. 50 Hz, [kV] 0,66 1,0 6,0
Maximum voltage A.C. 50 Hz, [kV] 0,72 1,2 7,2
Test voltage A.C. 50 Hz, 10 minutes, [kV] 3,0 3,5 15,0
Resistance of insulation at +70°C, not less than, [MOhms x km] 0,005 0,005 0,05
Max. operating temperature of conductor, [°C] +70
Temperature of conductors in emergency operation, [°C] +80
Max. temperature of short current during 4 s., [°C] +160
Temperature of environment, [°C] -50/+50
Humidity at 35°C, [%] 98
Installation at temperature not less than, [°C] -15
Bending radius of cable, [outer diameter]: - singlecore 10; - multicore 7.5
Length of cable for rated voltage 0.6-1 kV, not less, [m]:
- cross-section of main cable conductors up to 16 sq. mm 450
- cross-section of main conductors 25 up to 70 sq. mm 300
- cross-section of main conductors 95 sq. mm and more 200
Length of cable for rated voltage 6 kV, not less [m]:
- cross-section of main cable conductors 7-10 sq. mm 450
- cross-section of main conductors 95-120 sq. mm 400
- cross-section of main conductors 150 sq. mm and more 350
Cable lifetime, [years] 30
Guarantee period, [years] 5

Power cable NYM, BBГ:
1. Conductor. 2. Insulation. 3. Filling. 4. Outer sheath.
Power cable ABБбШв:
1. Conductor. 2. Insulation. 3. Belt insulation. 4. Armour. 5. Bitumen. 6. PETF tape. 7. Outer sheath.

Browse the categories on the page to search the necessary power cable and wire.
Visit our capabilities page to learn more about materials offerings.

Application:

Cables are used for electricity transmission and distribution in industry and municipal electric networks. Cables should be installed in fixed electric networks:
- In soil, irrespective of corrosion activity and, routs where there are stray currents and in highly wet soil;
- In cable lines, structures, overpasses, tunnels, ducts, wet and partially flooded rooms with medium and high corrosion activity;
- If there is danger of mechanical damage during operation it is recommended to use armored cable;
- Installation in fire dangerous and explosive zones.

Power cable NYM-J, NYM-O (DIN VDE 0250 - 204). Elements of cable design: copper cable conductors, PVC insulation, filling, PVC sheath. Cables are intended for installation of
wiring:
• in residential and public buildings. May be laid under, inside and above the plaster;
• in brickwork and concrete;
• in the open air protected from the direct sunlight. May be installed in ducts and channels.
Cables do not distribute burning in case of single laying (IEC 60332-1).

Power cable ABBГ, ABBГ-T, ABBГ-XЛ (IEC 60502-2, TT). Elements of cable design: aluminium cable conductors, PVC insulation, PVC sheath. Cables are intended for installation:
• in air, if there is no danger of mechanical damage;
• in dry or damp premises, conduits, ducts, mines, collectors, industrial premises and often-flooded premises with low, medium and high corrosion activity;
• in special cable overpasses and bridges;
• in fire dangerous premises;
• in explosive zones of B-Ib, B-Ig, B-II, B-IIa classes.
Cables are produced for vertical, inclined and horizontal lines. Cables can be used in places subject to vibration. Cables do not distribute burning in case of single laying (IEC 60332-1).

BBГ, BBГ-T, BBГ-1-XЛ (IEC 60502-2, TT). Elements of cable design: copper cable conductors, PVC insulation, PVC sheath. The same as ABBГ and also for installation in group lighting network in explosive zone of B-Ia class.

ABBГ-П, ABBГ-П-T (IEC 60502-1). The same as ABBГ and BBГ, but flat cables.

ABBГ3, BBГ3 (IEC 60502-1). The same as ABBГ and BBГ, but for supplying electric units, if compactness is required at the lead in electric equipment.

ABBГнг-LS. Elements of cable design: aluminium or copper cable conductors, PVC insulation, PVC sheath. Do not distribute burning in case of laying in bundles (IEC 60332-3, category A). Low smoke at burning (IEC 61034-1, 2).

Power cable ABБбШв, BБбШв (IEC 60502-1). Cables are intended for installation:
• in soil (trenches) with low, medium or high corrosion activity, in area subject to stray currents influence, if cable is not subject to tensile efforts;
• in air, if there is danger of mechanical damage;
• in dry or damp premises, conduits, ducts, mines, collectors, industrial premises and oftenflooded premises with low, medium and high corrosion activity;
• in fire dangerous premises;
• in explosive zones.
Power cables are produced for vertical, inclined and horizontal lines. Cable do not distribute burning in case of single laying (IEC 60332-1) - exclud. cable types ABBБ, BBБ.

Power cable ABБбШвз, BБбШвз (IEC 60502-1). Elements of cable design: aluminium or copper conductors, PVC insulation, tape armour, outer covering. The same as ABБбШв and BБбШв, but for supplying electric units, if compactness is required at the lead in electric equipment.

Power cable ABБбШнг, BБбШнг (IEC 60502-1). For installation in cable premises in underground (subway), in fire-dangerous and explosive area, if there is no tensile efforts and if there is a risk of mechanical influence to cable. It is possible to install cables in tubes and in soil (trenches) if there is an additional protection from mechanical damage. Do not distribute burning in case of laying in bundles (IEC 60332-3, A and B categories). For cables “нг-LS” - low smoke at burning.

ABB. Elements of cable design: aluminium cable conductors, PVC insulation, PVC sheath. For installation in cable structures and premises if there is no danger of mechanical damage.

Other power cables:
ЭBT. Power cable for power transmission in coal mines. Supplementary cores are intended for connection to electrical units and apparatus.
ABB. For installation in cable structures and premises if there is no danger of mechanical damage.

Cable Wire
Control Cable
Electrical Cables for Fixed Installation. Part 1

Electrical Cables for Fixed Installation. Part 1

2009-10-11T02:13:00.000-07:00

1. electrical cables for fixed installation with PVC and rubber insulation

Type of cable conductor: "no mark" - multiwire conductor; "ож" - solid conductor.

Type of cable conductor for control cables: "no mark" - solid conductor; "мн" - multiwire conductor.

Cross-section, mm.sq.

Number of cores.

Cable voltage.

Climatic performance: "no mark" - for temperate and cold climate; "T" - for tropical climate.

Shape: "no mark" - round; "П" - flat.

Screen: "Э" - copper tape screen.

Cable protective covering:
"Г" - without outer sheath;
"Б" - steel or galvanized steel tape armoring, fibrous materials, impregnated with bitumen and compound, preventing of lays sticking together;
"БГ" - steel or galvanized steel tape armoring, covered with bitumen and compound, preventing of lays sticking together;
"БбШв" - steel tape armoring, covered with bitumen and plastic tapes, or galvanized steel tape armoring and protective extruded PVC sheath;
"ПбШв" - galvanized steel wire armoring and protective extruded PVC sheath;
"БВ" - steel tape armoring and protective PVC sheath;
"БбШнг" - galvanized steel tape armoring and flame-retardant PVC sheath.

Cable outer sheath material:
"B" - PVC outer sheath;
"H" - flame retardant rubber outer sheath;
"нг" - flame retardant PVC sheath;
"з" - sheath extruded with filling gaps between cores.

Material of cable Insulation:
"B" - PVC insulation, operating temperature of cable conductor 70'C;
"P" - rubber insulation, operating temperature of conductor 70'C;
"PT" - EPR insulation, operating temperature of conductor 90'C;
"П" - polyethylene insulation, operating temperature of conductor 70'C;
"Пв" - XLPE insulation, operating temperature of conductor 90'C.

Type of cable: "no mark" - power cable; "K" - control cable.

Material of cable conductor: "no mark" - copper, solid (ож) round <50>50 mm.sq; "A" - aluminium, solid (ож) <240>50 mm.sq; multiwire round and sector >70 mm.sq.

Browse the categories on the page to search the necessary cable and wire.
Visit our capabilities page to learn more about materials offerings.

Note:
in cables of ВРГ, НРГ, ВРБ, НРБ, ВРБГ, НРБГ (including those with aluminium conductor) the first letter means the type of cable sheath, second - the type of cable insulation.

Example:
АВБбШв-T 1 4x16ож
- power cable with aluminium conductors, with PVC insulation, armored with galvanized steel tapes, in PVC outer sheath, tropical performance, nominal voltage 1kV, four cores, 16 mm.sq, solid conductors.

Cables and Wires for You

2009-10-10T10:59:00.000-07:00

Our company Cable Wire was estabilished in July 1995.

In May, 1996 the first products were put outbare aluminium conductors.

By 2001 Cable Wire delivered to its customers cables in rubber insulation, power cables in paper and PVC insulation, winding wires.

Constantly increasing the production, expanding the range of products, Cable Wire has become a supplier of cables to 70 countries, including USA, Germany, China.

In 2004 new managers came to JSC Cable Wire and have formed a highly professional market-minded team.

Main sales principals are perfect fulfillment of all obligations, personal attention to every customer and flexible price policy.

In 2004 the company Cable Wire obtained an ISO 9001-94 Certificate.

The quality control of cables is carried out on the base of modern, constantly renovating testing facilities and skilled personnel of testing laboratories let carry out all the tests, required by international standards and consumers, with all types of products, manufactured by Cable Wire.

Accreditation attest, certifying that, "Testing Center of cable products" of JSC Cable Wire is accredited as technically competent testing laboratory in system of certification GOST R (RNSR), is received by the company.

At present JSC Cable Wire employs 1047 persons.

Today Cable Wire can offer a diverse range of products, including Oil-filled cables for voltage from 110 kV up to 500 kV, Power cables with paper insulation for voltage up to 35 kV, Power cables with plastic insulation for voltage from 1 kV up to 6 kV, Control cables, Power cords and wires, Power cables with rubber insulation for voltage up to 10 kV, Bare conductors, Self-supporting wires, Enameled wires, Cables for special applications and other (more than 6000 types and sizes).

Browse the categories on the page to search the necessary cable and wire.
Visit our capabilities page to learn more about materials offerings.

Cable Wire's partners are:

- Electricity Companies;

- Oil and Gas Companies;

- Machine-building Industry.

Cable Wire shares up to 40% of RF Market of power cables, up to 30% of cables for submerged oil pumps and up to 20% of enameled wires.

JSC Cable Wire is a modern, dynamic and powerful enterprise, one of three largest manufacturers of cable in RF.

JSC Cable Wire specializes in the manufacture of the following cable products:

bare wires;
insulated wires;
wires for electrical installation;
power cables with different type of insulation;
control cables;
control cables with stationary laying;
radio-frequency cable.

We master the manufacture of uninsulated and insulated aerial-bundled conductors according to international standards ASTM, BS, DIN/VDE.

To our opinion, the company has the following resources:

Power and flexibility of production
Experience and qualification of staff
Financial stability
Competitive prices for our products
High quality of manufactured products

Cooperating with Cable Wire, you always can rely on high level of technique and technology and many years experience of Cable Wire.

The main aim of our successful activity is manufacture and delivery of products in accordance with the requirements of the customer. We developed mission and strategy of the enterprise. The quality system is the instrument for realization of these aims.

The operating Cable Wire's quality system is certificated by foreign certification body TUV CERT and national certification body in conformity to the requirements of the international standard ISO 9001.

The important stage for improvement of Cable Wire's quality system is the introduction of new versions of ISO 9000-2000 and sense of activity is oriented approach to quality management.

To protect people and environment from potential effects of the activity, to increase ecological culture and to achieve advantages under competition, Cable Wire sets the new aims for introduction of environment quality management system.

Electrical Cables for Fixed Installation. Part 1
Control Cable
Power Cable